Push-Pull Standard Control Cable Assembly

 
Push - Pull Standard Industrial Control Cable Assembly , Mechanical Control Cable Assembly

 
Product Description 
We assemble Push-Pull Control cables. These cables provide a means of transmitting linear motion from one location to another. They offer ease of installation as well as superior performance.
We use Low Friction EXT materials which feature a binder wire for structural integrity, tight minimum bend radius, and a PTFE covered innermember for efficient and smooth operation.
Applications include : implement control, throttle control, PTO activation, Valve actuation, Transmission Shift.

Features

• Typical temperature range

  -65°F-230°F(Bristow)

  -65°F-230°F(Utility)

  -65°F --230°F(Low Friction EXT)

  -65°F-230°F(Low Friction)
• Tough/durable materials
• Long lasting seals
• Environmentally protected

Applications

• Implement control
• Throttle control
• PTO/4WD activation
• Valve actuation
• Remote battery disconnect
• Remote electrical disconnect
• Transmission shift
• Hydrostatic drives
• Latches

Characteristic

• Durable material
• Long life seal
• Environmental protection
• Easy to install, performance excellence

Comparison

 
The Bristow®

Type control is an economical construction for applications which do not require tight bend radii, and are temperature rated for use from a low of -65°F to a peak of +230°F.
The Utility Style

adds a binder wire for structural integrity and a tighter minimum bend radius than other controls.
Low Friction EXT

controls have the same advantages as utility with an added plastic covered innermember which provides improved efficiency.
Low Friction controls provide the standard of excellence for industrial controls. Features include a binder wire for structural integrity, tight minimum bend radius, and PTFE covered innermember for the ultimate in efficient, smooth operation. Temperature rated for use from a low of -65°F to a peak of +230°F, they will provide long life in the most demanding applications.

Technical Parameters

A.Custom Length Cables

 Load Capacities and length of travel

B.Conduit End Fittings
Type T  Threaded Conduit End Fitting for bulkhead mounting.
Type G  Grooved Conduit End Fitting for mounting with U-bolts or clamps.

•Grooved End Fittings

•Threaded End Fittings

•Threaded On One Side, Grooved On The Other

C.Overall Length and Travel in Inches

FOR REPLACEMENT CABLES                                      

A. Remove old cable.
B. Measure length as shown below.
C. Measure length of travel. 1'' through 6''.
D. Determine size of thread “F.” Select basic part number from table above.

--------------------------------------------------------------------------------------------------------------------------

FOR NEW CABLES
A. Determine overall length.
B. Measure travel required. Add ¼'' and then round upward to nearest whole inch.
C. Determine loads and select basic part number from table A.

Standard Length Industrial  /  Performance Cables & Accessories
• Utility Style adds a binder wire for structural integrity and a tighter minimum bend radius than  other controls.
• Low Friction controls have the same advantages as Utility with an added plastic covered innermember which provides improved efficiency.
• Blue Max™ is the high performance control cable with extreme low friction and minimal loss of motion. True 4" minimum bend radius, lubed for life and outer jacket is resistant to abrasions, gasoline, diesel and chemicals. Designed for long runs with complicated cable routing while being extremely efficient on shorter runs. All exposed fittings/parts are stainless steel.

These 3" travel cables have #10-32 (3/16") end rod threads and are ideal for use as fuel shut-off, parachute release, throttle and shift cables.

 
Packing and Shipping
Ordering Codes — UNF Threads
Duty — Size —— ¼
Output Options (Bulkhead Clamp) —— BC
Travel (inches) —— 3
Cable Length (inches) —— XXX
Ordering Codes — Metric Threads
Duty — Size —— M6
Output Options (Bulkhead Clamp) —— BC
Travel (mm) —— 75
Cable Length (mm) —— XXX

FAQ
Q: What is the brand of the Control Cables?
A: The brand of the Control Cables is PHIDIX.
Q: What is the model number of the Control Cables?
A: The model number of the Control Cables is PHIDIX.
Q: Where is the Control Cables manufactured?
A: The Control Cables is manufactured in Shanghai.
Q: What are the specifications of the Control Cables?
A: Please contact us for the specifications of the Control Cables.